Goto Section: 25.220 | 25.222 | Table of Contents
FCC 25.221
Revised as of October 1, 2019
Goto Year:2018 |
2020
§ 25.221 Blanket licensing provisions for ESVs operating with GSO FSS space
stations in the 3700-4200 MHz and 5925-6425 MHz bands.
(a) The following ongoing requirements govern all ESV licensees and
operations in the 3700-4200 MHz (space-to-Earth) and 5925-6425 MHz
(Earth-to-space) bands transmitting to GSO satellites in the
Fixed-Satellite Service. ESV licensees must comply with the
requirements in paragraph (a)(1), (a)(2) or (a)(3) of this section and
all of the requirements set forth in paragraphs (a)(4) through (a)(13)
of this section. Paragraph (b) of this section identifies items that
must be included in the application for ESV operations to demonstrate
that these ongoing requirements will be met.
(1) The following requirements shall apply to an ESV that uses
transmitters with off-axis effective isotropically radiated power
(EIRP) spectral-densities lower than or equal to the levels in
paragraph (a)(1)(i) of this section. An ESV, or ESV system, operating
under this section shall provide a detailed demonstration as described
in paragraph (b)(1) of this section. The ESV transmitter must also
comply with the antenna pointing and cessation of emission requirements
in paragraphs (a)(1)(ii) and (a)(1)(iii) of this section.
(i)(A) Off-axis EIRP spectral density emitted in the plane tangent to
the GSO arc, as defined in § 25.103, shall not exceed the following
values:
26.3-25logθ dBW/4 kHz for 1.5° ≤ θ ≤ 7°.
5.3 dBW/4 kHz for 7° < θ ≤ 9.2°.
29.3-25logθ dBW/4 kHz for 9.2° < θ ≤ 48°.
−12.7 dBW/4 kHz for 48° < θ ≤ 180°.
Where theta (θ) is the angle in degrees from a line from the earth
station antenna to the assigned orbital location of the target
satellite. The EIRP density levels specified for θ > 7° may be exceeded
by up to 3 dB in up to 10% of the range of theta (θ) angles from
±7-180°, and by up to 6 dB in the region of main reflector spillover
energy.
(B) In the plane perpendicular to the GSO arc, as defined in § 25.103,
EIRP spectral density of co-polarized signals shall not exceed the
following values:
29.3-25logθ dBW/4 kHz for 3.0° ≤ θ ≤ 48°.
−12.7 dBW/4 kHz for 48° < θ ≤ 180°.
Where θ is as defined in paragraph (a)(1)(i)(A) of this section. These
EIRP density levels may be exceeded by up to 6 dB in the region of main
reflector spillover energy and in up to 10% of the range of θ angles
not included in that region, on each side of the line from the earth
station to the target satellite.
(C) The off-axis EIRP spectral-density of cross-polarized signals shall
not exceed the following values in the plane tangent to the GSO arc or
in the plane perpendicular to the GSO arc:
16.3-25logθ dBW/4 kHz for 1.8° ≤ θ ≤ 7.0°.
Where θ is as defined in paragraph (a)(1)(i)(A) of this section.
(ii) Except for ESV systems operating under paragraph (a)(3) of this
section, each ESV transmitter must meet one of the following antenna
pointing error requirements:
(A) Each ESV transmitter shall maintain a pointing error of less than
or equal to 0.2° between the orbital location of the target satellite
and the axis of the main lobe of the ESV antenna, or
(B) Each ESV transmitter shall maintain the declared maximum antenna
pointing error that may be greater than 0.2° provided that the ESV does
not exceed the off-axis EIRP spectral-density limits in paragraph
(a)(1)(i) of this section, taking into account the antenna pointing
error.
(iii) Except for ESV systems operating under paragraph (a)(3) of this
section, each ESV transmitter must meet one of the following cessation
of emission requirements:
(A) For ESVs operating under paragraph (a)(1)(ii)(A) of this section,
all emissions from the ESV shall automatically cease within 100
milliseconds if the angle between the orbital location of the target
satellite and the axis of the main lobe of the ESV antenna exceeds
0.5°, and transmission will not resume until such angle is less than or
equal to 0.2°, or
(B) For ESV transmitters operating under paragraph (a)(1)(ii)(B) of
this section, all emissions from the ESV shall automatically cease
within 100 milliseconds if the angle between the orbital location of
the target satellite and the axis of the main lobe of the ESV antenna
exceeds the declared maximum antenna pointing error and shall not
resume transmissions until such angle is less than or equal to the
declared maximum antenna pointing error.
(2) The following requirements apply to ESV systems that operate with
off-axis EIRP spectral-densities in excess of the levels in paragraph
(a)(1)(i) or (a)(3)(i) of this section under licenses granted based on
certifications filed pursuant to paragraph (b)(2) of this section.
(i) An ESV or ESV system licensed based on certifications filed
pursuant to paragraph (b)(2) of this section must operate in accordance
with the off-axis EIRP density specifications provided to the target
satellite operator in order to obtain the certifications.
(ii) Any ESV transmitter operating under a license granted based on
certifications filed pursuant to paragraph (b)(2) of this section must
be self-monitoring and capable of shutting itself off and must cease or
reduce emissions within 100 milliseconds after generating off-axis
EIRP-density in excess of the specifications supplied to the target
satellite operator.
(iii) A system with variable power control of individual ESV
transmitters must monitor the aggregate off-axis EIRP density from
simultaneously transmitting ESV transmitters at the system's network
control and monitoring center. If simultaneous operation of two or more
ESV transmitters causes aggregate off-axis EIRP density to exceed the
off-axis EIRP-density specifications supplied to the target satellite
operator, the network control and monitoring center must command those
transmitters to cease emissions or reduce the aggregate EIRP density to
a level at or below those specifications, and the transmitters must
comply within 100 milliseconds of receiving the command.
(3) The following requirements apply to an ESV system that uses
variable power control of individual earth stations transmitting
simultaneously in the same frequencies to the same target satellite,
unless the ESV system operates pursuant to paragraph (a)(2) of this
section.
(i) Aggregate EIRP density from co-frequency earth stations in each
target satellite receiving beam, not resulting from colliding data
bursts transmitted pursuant to a contention protocol, will not exceed
the limits defined in paragraph (a)(1)(i) of this section.
(ii) Each ESV transmitter must be self-monitoring and capable of
shutting itself off and must cease or reduce emissions within 100
milliseconds after generating off-axis EIRP density in excess of the
limit in paragraph (a)(3)(i) of this section.
(iii) Aggregate power density from simultaneously transmitting ESV
transmitters must be monitored at the system's network control and
monitoring center. If simultaneous operation of two or more ESV
transmitters causes aggregate off-axis EIRP density to exceed the
off-axis EIRP density limit in paragraph (a)(3)(i) of this section, the
network control and monitoring center must command those transmitters
to cease emissions or reduce the aggregate EIRP density to a level at
or below that limit, and those transmitters must comply within 100
milliseconds of receiving the command.
(4) There shall be a point of contact in the United States, with phone
number and address, available 24 hours a day, seven days a week, with
authority and ability to cease all emissions from the ESVs, either
directly or through the facilities of a U.S. Hub or a Hub located in
another country with which the United States has a bilateral agreement
that enables such cessation of emissions.
(5) For each ESV transmitter, a record of the ship location (i.e.,
latitude/longitude), transmit frequency, channel bandwidth and
satellite used shall be time annotated and maintained for a period of
not less than 1 year. Records will be recorded at time intervals no
greater than every 20 minutes while the ESV is transmitting. The ESV
operator will make this data available upon request to a coordinator,
fixed system operator, Fixed-Satellite system operator, or the
Commission within 24 hours of the request.
(6) ESV operators communicating with vessels of foreign registry must
maintain detailed information on each vessel's country of registry and
a point of contact for the relevant administration responsible for
licensing ESVs.
(7) ESV operators shall control all ESVs by a hub earth station located
in the United States, except that an ESV on U.S.-registered vessels may
operate under control of a hub earth station location outside the
United States provided the ESV operator maintains a point of contact
within the United States that will have the capability and authority to
cause an ESV on a U.S.-registered vessel to cease transmitting if
necessary.
(8) ESV operators transmitting in the 5925-6425 MHz (Earth-to-space)
frequency band to GSO satellites in the Fixed-Satellite Service (FSS)
shall not seek to coordinate, in any geographic location, more than 36
megahertz of uplink bandwidth on each of no more than two GSO FSS
satellites.
(9) ESVs shall not operate in the 5925-6425 MHz (Earth-to-space) and
3700-4200 MHz (space-to-Earth) frequency bands on vessels smaller than
300 gross tons.
(10) ESVs, operating while docked, that complete coordination with
terrestrial stations in the 3700-4200 MHz band in accordance with
§ 25.251, shall receive protection from such terrestrial stations in
accordance with the coordination agreements, for 180 days, renewable
for 180 days.
(11) ESVs in motion shall not claim protection from harmful
interference from any authorized terrestrial stations or lawfully
operating satellites to which frequencies are either already assigned,
or may be assigned in the future in the 3700-4200 MHz (space-to-Earth)
frequency band.
(12) ESVs operating within 200 km from the baseline of the United
States, or within 200 km from a U.S.-licensed fixed service offshore
installation, shall complete coordination with potentially affected
U.S.-licensed fixed service operators prior to operation. The
coordination method and the interference criteria objective shall be
determined by the frequency coordinator. The details of the
coordination shall be maintained and available at the frequency
coordinator, and shall be filed with the Commission electronically via
the International Bureau Filing System
(http://licensing.fcc.gov/myibfs/) to be placed on public notice. The
coordination notifications must be filed in the form of a statement
referencing the relevant call signs and file numbers. Operation of each
individual ESV may commence immediately after the public notice is
released that identifies the notification sent to the Commission.
Continuance of operation of that ESV for the duration of the
coordination term shall be dependent upon successful completion of the
normal public notice process. If, prior to the end of the 30-day
comment period of the public notice, any objections are received from
U.S.-licensed Fixed Service operators that have been excluded from
coordination, the ESV licensee must immediately cease operation of that
particular station on frequencies used by the affected U.S.-licensed
Fixed Service station until the coordination dispute is resolved and
the ESV licensee informs the Commission of the resolution. As used in
this section, “baseline” means the line from which maritime zones are
measured. The baseline is a combination of the low-water line and
closing lines across the mouths of inland water bodies and is defined
by a series of baseline points that include islands and “low-water
elevations,” as determined by the U.S. Department of State's Baseline
Committee.
(13) ESV operators must automatically cease transmission if the ESV
operates in violation of the terms of its coordination agreement,
including, but not limited to, conditions related to speed of the
vessel or if the ESV travels outside the coordinated area, if within
200 km from the baseline of the United States, or within 200 km from a
U.S.-licensed fixed service offshore installation. Transmissions may be
controlled by the ESV network. The frequency coordinator may decide
whether ESV operators should automatically cease transmissions if the
vessel falls below a prescribed speed within a prescribed geographic
area.
(b) Applications for ESV operation in the 5925-6425 MHz
(Earth-to-space) band to GSO satellites in the FSS must include, in
addition to the particulars of operation identified on FCC Form 312,
and associated Schedule B, applicable technical demonstrations or
certifications pursuant to paragraph (b)(1), (b)(2), or (b)(3) of this
section and the documentation identified in paragraphs (b)(4) through
(b)(6) of this section.
(1) An ESV applicant proposing to implement a transmitter under
paragraph (a)(1) of this section must provide the information required
by § 25.115(g)(1). An applicant proposing to implement a transmitter
under paragraph (a)(1)(ii)(A) of this section must also provide the
certifications identified in paragraph (b)(1)(iii) of this section. An
ESV applicant proposing to implement a transmitter under paragraph
(a)(1)(ii)(B) of this section must also provide the demonstrations
identified in paragraph (b)(1)(iv) of this section.
(i)-(ii) [Reserved]
(iii) An ESV applicant proposing to implement a transmitter under
paragraph (a)(1)(ii)(A) of this section, must provide a certification
from the equipment manufacturer stating that the antenna tracking
system will maintain a pointing error of less than or equal to 0.2°
between the orbital location of the target satellite and the axis of
the main lobe of the ESV antenna and that the antenna tracking system
is capable of ceasing emissions within 100 milliseconds if the angle
between the orbital location of the target satellite and the axis of
the main lobe of the ESV antenna exceeds 0.5°.
(iv) An ESV applicant proposing to implement a transmitter under
paragraph (a)(1)(ii)(B) of this section must:
(A) Declare, in its application, a maximum antenna pointing error and
demonstrate that the maximum antenna pointing error can be achieved
without exceeding the off-axis EIRP spectral-density limits in
paragraph (a)(1)(i) of this section; and
(B) Demonstrate that the ESV transmitter can detect if the transmitter
exceeds the declared maximum antenna pointing error and can cease
transmission within 100 milliseconds if the angle between the orbital
location of the target satellite and the axis of the main lobe of the
ESV antenna exceeds the declared maximum antenna pointing error, and
will not resume transmissions until the angle between the orbital
location of the target satellite and the axis of the main lobe of the
ESV antenna is less than or equal to the declared maximum antenna
pointing error.
(2) An applicant proposing to operate with off-axis EIRP density in
excess of the levels specified in paragraph (a)(1)(i) or (a)(3)(i) of
this section must provide the following in exhibits to its earth
station application:
(i) Off-axis EIRP density data pursuant to § 25.115(g)(1):
(ii) The certifications required by § 25.220(d);
(iii) A detailed showing that each ESV transmitter in the system will
automatically cease or reduce emissions within 100 milliseconds after
generating EIRP density exceeding specifications provided to the target
satellite operator;
(iv) A detailed showing that the aggregate power density from
simultaneously transmitting ESV transmitters will be monitored at the
system's network control and monitoring center; that if simultaneous
operation of two or more ESV transmitters causes the aggregate off-axis
EIRP density to exceed the off-axis EIRP density specifications
supplied to the target satellite operator, the network control and
monitoring center will command those transmitters to cease emissions or
reduce the aggregate EIRP density to a level at or below those
specifications; and that those transmitters will comply within 100
milliseconds of receiving the command; and
(v) A certification that the ESV system will operate in compliance with
the power limits in § 25.204(h).
(3) An applicant proposing to implement an ESV system subject to
paragraph (a)(3) of this section must provide the following information
in exhibits to its earth station application:
(i) Off-axis EIRP density data pursuant to § 25.115(g)(1);
(ii) A detailed showing of the measures that will be employed to
maintain aggregate EIRP density at or below the limit in paragraph
(a)(3)(i) of this section;
(iii) A detailed showing that each ESV terminal will automatically
cease or reduce emissions within 100 milliseconds after generating
off-axis EIRP density exceeding the limit in paragraph (a)(3)(i) of
this section;
(iv) A detailed showing that the aggregate power density from
simultaneously transmitting ESV transmitters will be monitored at the
system's network control and monitoring center; that if simultaneous
operation of two or more ESV transmitters causes aggregate off-axis
EIRP density to exceed the off-axis EIRP density limit in paragraph
(a)(3)(i) of this section, the network control and monitoring center
will command those transmitters to cease emissions or reduce the
aggregate EIRP density to a level at or below that limit; and that
those transmitters will comply within 100 milliseconds of receiving the
command; and
(v) Certification that the ESV system will operate in compliance with
the power limits in § 25.204(h).
(4) There shall be an exhibit included with the application describing
the geographic area(s) in which the ESVs will operate.
(5) The point of contact information referred to in paragraph (a)(3) of
this section and, if applicable, paragraph (a)(6) of this section, must
be included in the application.
(6) ESVs that exceed the radiation guidelines of § 1.1310 of this
chapter, Radiofrequency radiation exposure limits, must provide, with
their environmental assessment, a plan for mitigation of radiation
exposure to the extent required to meet those guidelines.
(7) Except for ESV systems operating pursuant to paragraph (a)(2) of
this section, ESV systems authorized pursuant to this section shall be
eligible for a license that lists Permitted List as an authorized point
of communication.
[ 74 FR 47102 , Sept. 15, 2009, as amended at 77 FR 50050 , Aug. 20, 2012;
78 FR 8429 , Feb. 6, 2013; 78 FR 29062 , May 17, 2013; 79 FR 8324 , Feb.
12, 2014; 81 FR 55342 , Aug. 18, 2016]
return arrow Back to Top
Goto Section: 25.220 | 25.222
Goto Year: 2018 |
2020
CiteFind - See documents on FCC website that
cite this rule
Want to support this service?
Thanks!
Report errors in
this rule. Since these rules are converted to HTML by machine, it's possible errors have been made. Please
help us improve these rules by clicking the Report FCC Rule Errors link to report an error.
hallikainen.com
Helping make public information public